I just recently moved to Florida from the west coast and am on a low, set income. This is a membrane that separates the tile from direct contact with the concrete, helping to provide support for any weaknesses in the concrete due to shrinkage or expansion. Can you use hardy board for a sub floor. From that point on the installation proceeds in the traditional fashion. Wear rubber gloves and safety glasses. It is not concrete underneath, I am assuming it is plywood underneath old mortar. Given the base plywood can I just use the standard thinset, or this thinset with an additive or a totally different thinset? Test by sprinkling water on various areas of the subfloor.
Write to Zolton Cohen, Around the House, P. You can either roll on a liquid latex membrane, or put down a peel-and-stick crack prevention mat over the entire concrete subfloor. Interior-grade plywood and particleboard are not considered strong enough for a tile installation. Repeat this process until you've filled all the joints with grout, then immediately begin wiping excess grout off the face of the tiles using a wet sponge. This provides added strength and minimizes flexing at the joints.
Thank you for your help! Notches should all run in the same direction. I know we need some kind of waterproof barrier to protect the wood from warping. Eliminating movement and leveling the subfloor prevents premature cracking and breaking of the adhesive and the tiles. How do you know you have the right modified thin-set? I have a roto zip saw, but did not see an attachment that would work. It essentially makes the floor one solid structure rather than a joist by joist structure, thus if the floor gives it gives over a wider span rather than between joists. That way you're not running back to the store.
Use a Patented Technique to Guarantee Success Laying tile over a plywood subfloor can be a bit tricky, but if you take the time to prepare the sub floor properly, you can enjoy a new tile floor that will last for a lifetime. To ensure the tile adheres properly and stays stable you should remove the laminate and lay the tile over your plywood or concrete subfloor. I still get calls for more work after being out of it for 10 years because my work held up. To see if your floor is out of level, all you have to do is measure between the level laser line and the floor at various locations along the room's perimeter. Any comments would be appreciated concerning my kitchen floor install. Take care not to mix too large a batch of thin-set. Most tile installers tell me to forget it.
Once you have allowed this to set and can walk on it, measure the space you have along walls and other border areas, minus the grout line, and mark where tiles need to be cut to fill these odd spaces. I was thinking of pouring a thin layer of self leveling cement, and putting the backer board on top of this. It is a wonderful resource for those of us who prefer to do our own work. We have a small area of concrete foundation that we need to patch and level prior to ceramic tile installation 12×12 tiles. It is still in good shape, however, my little girl want to run bare foot on them and she got alot of splinters on her feet.
The only way to do the job right is to vapor tight the areas and float it out for a true install that will live longer than most people will own the house. Tip If you wish to salvage the tile pieces, work slowly to avoid breaking them. A tight, unmoving bond between mortar and subfloor causes cracking. Well worth the price when you consider the time and back breaking work of using hardie backer or cement board. They are nailed to floor joists and that is it! We hated using concrete backerboard because it needs to be installed with thinset under it or it could crack. Because of time, we will be doing this in sections.
We can feel the floor give in some spots. Who should check it out and how can it be repaired with minimal damage to first story ceiling? I want to tile the floor but am concerned about trying to level it all before starting with the tile and backerboard. The main area of the basement was flashed in four, parallel runs. Also, the tile is just hanging on the wood without any backer board, is this normal? Tile is hard and will break or dislodge if the surface bends under the load, and many wood surfaces can expand or contract, negatively impacting their ability to stay level and support the weight. After taking out the old flooring on closer inspection I see that the flooring is supported by 5. It's lighter, easier to cut and prevents tile from cracking.
First he applies a coat of adhesive to the subfloor, using a straight trowel. When in doubt add blocking in the joists if you can get at them and more screws in the subfloor to make sure. While the tile may come up in large pieces, the concrete board is going to require significant time to remove and rarely comes up in chunks. Ford Says: My husband and I are renovating a rental house and want to use ceramic tile in the kitchen. Any help would be welcomed.
But ceramic, porcelain, and , along with their service components of thinset and grout, are far too fragile to withstand even the slightest substrate movement. The wood floor boards are somewhat warped and not in the best of shape. Do this at intervals recommended in the backer board instructions usually every 8 inches to ensure a firm foundation for the tile. If it is unsealed, see tips at the bottom of this guide. Do you know of a tool that will work for this? Thanks in advance for your help! It's not uncommon for subfloors to develop low spots or other imperfections over time, but before installing a new floor over one, it's very important to address these issues and make certain the subfloor is level.
We want to hear from you! And secondly, I have a couple spots where I found mold. If the mortar bed is uneven or cracked, apply a leveling or patching compound as needed first. The kitchen floor was originally a vinyl tile directly adhered to concrete. Thanks for any information you can give me. My basement floors are concrete so I like that you had photos explaining how to level them. I thought you might be able to tell me what would be the best idea, so I can get it done properly once and for all. If yes, what is recommended for under a woodburning stove.